What you put in, you'll get back ten fold
Members and searchers please be aware that some of our 'how to' guides do not currently show the intended help photos. This is because photobucket wants to charge a monthly amount for us to view our own pics. The photos are currently being replaced. If you need one of our guides and it is missing pics please let one of the Admin team know and we will make that one a priority for you.
Regards
Admin

Creepys new Black-un

A place for members to show off their pride and joy. Also room to document your projects.
scunninghamk
New
Posts: 13
Joined: Fri Dec 23, 2016 12:25 pm

Re: Creepys new Black-un

Postby scunninghamk » Mon Jun 26, 2017 2:15 pm

Speedy wrote:The Black un is looking great, well done. She used to sit low when on Rokkor coilovers then onto MeisterR that does needs sorting pronto.

IMG_0716.JPG





Sent from my iPhone using Tapatalk
scunninghamk
New
Posts: 13
Joined: Fri Dec 23, 2016 12:25 pm

Re: Creepys new Black-un

Postby scunninghamk » Mon Jun 26, 2017 2:18 pm

Reversing sensors!!!! If you reverse assuming you've got em, you'll find out too late you haven't.
I'm in the same boat as you mate 90% of the time I drive a modern space ship with lots of sensors then reverse the MX5 and.. have to be careful again.
Which sensors did you install and any hints?


Sent from my iPhone using Tapatalk
User avatar
Creepy
Just Run In
Posts: 44
Joined: Mon Sep 28, 2015 8:49 pm
Location: South Manchester

Re: Creepys new Black-un

Postby Creepy » Mon Jul 03, 2017 5:58 pm

scunninghamk wrote:Reversing sensors!!!! If you reverse assuming you've got em, you'll find out too late you haven't.
I'm in the same boat as you mate 90% of the time I drive a modern space ship with lots of sensors then reverse the MX5 and.. have to be careful again.
Which sensors did you install and any hints?


Sent from my iPhone using Tapatalk


This was the set I bought https://www.amazon.co.uk/gp/product/B00 ... UTF8&psc=1
They've been working fine since. Have to admit they're not as sensitive as the factory fitted sensors on my modern space ship but they do the job OK. I wouldn't like to reverse at speed using them as they're not the most sensitive. However, for the price they do a good job. Electrics are a piece of cake. Drilling the holes in the bumper and getting the spacing right is the difficult bit. However if you take your time and work from the centre outwards then it's not too hard. I put a line of masking take on the bumper so I could mark the points for drilling - then checked, checked again and got someone else to check before getting the drill out ! The buzzer is rather loud so I hit in the boot it's not so deafening.
Hope that helps.
Andy.
P.S. I'm sure I found a decent thread on how to fit the reversing sensors including the drilling - with some good photo's too. It may gave been a listing on another forum - but don't tell anyone! :-)
User avatar
Creepy
Just Run In
Posts: 44
Joined: Mon Sep 28, 2015 8:49 pm
Location: South Manchester

Re: Creepys new Black-un

Postby Creepy » Mon Jul 03, 2017 6:06 pm

Speedy wrote:The Black un is looking great, well done. She used to sit low when on Rokkor coilovers then onto MeisterR that does needs sorting pronto.

IMG_0716.JPG



Thanks for the positive feedback - appreciated :text-thankyouyellow:

My next job is to sort the ride height but I'm completely stumped on what to do. I've RTFM about a dozen times and MM has already told me (earlier thread) that only a couple of nuts need cracking and weighting the car before re-tightening. It SHOULD be an easy job, but I can't for the life of me work it out. I'll give MM a shout and maybe see if he's up for me paying a visit so he can give me an idiots lesson on car suspension. :doh:

Once winter arrives I am planning on upgrading the suspension - so that's another conversation to be had with MM :-)
User avatar
Mazda Mender
Site Admin
Posts: 11994
Joined: Tue Dec 06, 2011 6:18 pm
Location: Pie land,North west
Contact:

Re: Creepys new Black-un

Postby Mazda Mender » Mon Jul 03, 2017 11:27 pm

Creepy wrote:
Speedy wrote:The Black un is looking great, well done. She used to sit low when on Rokkor coilovers then onto MeisterR that does needs sorting pronto.

IMG_0716.JPG



Thanks for the positive feedback - appreciated :text-thankyouyellow:

My next job is to sort the ride height but I'm completely stumped on what to do. I've RTFM about a dozen times and MM has already told me (earlier thread) that only a couple of nuts need cracking and weighting the car before re-tightening. It SHOULD be an easy job, but I can't for the life of me work it out. I'll give MM a shout and maybe see if he's up for me paying a visit so he can give me an idiots lesson on car suspension. :doh:

Once winter arrives I am planning on upgrading the suspension - so that's another conversation to be had with MM :-)


I'll give you a bell tomoz buddy ;0)
M-m
The Disclaimer:-
This post is a natural product made from recycled electrons. The slight variations in spelling and grammar enhance its individual character and beauty and in no way are to be considered flaws or defects, the articles/answers/comments are provided for information purposes and they are not intended to substitute informed professional advice, I or mazdamenders.net cannot personally be hold responsible for any damage occurred from following this procedure or any injuries from it. Proceed at your own risk.


Mk 1 Eunos 93 black V.S II 1.8 fettled,
Mk 2 .1/4 Roadster 99 black & gold V.S 1.8 being rebuilt,
Mk 1 Eunos 90 1.6 (claimed by daughter)
Mk 1 Eunos 96 1.8 blue B2...being fettled
Mk1 Eunos 93 1.6 black S special being fettled
http://www.mx5oc.co.uk/ http://www.mx5nutz.com/forum/ http://miata.net/ http://www.autolinkuk.co.uk/
User avatar
Creepy
Just Run In
Posts: 44
Joined: Mon Sep 28, 2015 8:49 pm
Location: South Manchester

Re: Creepys new Black-un

Postby Creepy » Mon Sep 11, 2017 11:22 am

HI MM. Great to see you at the weekend and catch-up. I spent a couple of hours on Sunday taking a look at the suspension (rear) and making a stab at getting it lowered to the correct height (see previous pics). i.e. Wheel off, raise the car on ramps, crack the bolts (4?), jack up the suspension (Carefully!) , tighten bolts, wheel on, lower car.
Problem being this isn't working for me, boo hoo. I'm probably cracking the wrong nuts/bolts - so have included a pic below of nuts/bolts I'm loosening (its an old pic just to show you the nuts I'm loosening)? The one issue that may be problem is the 17mm bolt (which I've circled in Red) won't bloody budge. I can remove the nut but the long bolt is completely seized in-place - therefore I guess it won't be moving when I jack-up the suspension? I've soaked it in WD40 and will leave for a couple of days to see if that helps but it's seized tight despite giving it a few good thumps with a mallet (Careful not to wreck the bolt obviously). Interestingly my workshop manual notes this is a common problem as part of the bolt is open to the elements so it gets proper seized.

So... Can you confirm please;
1) if I'm cracking the correct nuts/bolts?
2) Any tips on how to get the 17mm bolt moving (circled in Red on the picture below)
3) What's a really good penetrating fluid/oil? I've only got WD40 at the moment. Is there anything better worth investing in? e.g. English Abrasives PlusGas

Cheers,
andy.

P.S. Ordered the Vauxhall interior lights this morning from eBay and found the excellent article on the forum.
Attachments
sorting my suspension - bolts to loosen.jpg
sorting my suspension - bolts to loosen.jpg (343.03 KiB) Viewed 44 times
User avatar
Mazda Mender
Site Admin
Posts: 11994
Joined: Tue Dec 06, 2011 6:18 pm
Location: Pie land,North west
Contact:

Re: Creepys new Black-un

Postby Mazda Mender » Mon Sep 11, 2017 12:08 pm

your cracking the wrong bolt buddy....go further inboard the the 17mm bolt in the wishbone.
M-m
The Disclaimer:-
This post is a natural product made from recycled electrons. The slight variations in spelling and grammar enhance its individual character and beauty and in no way are to be considered flaws or defects, the articles/answers/comments are provided for information purposes and they are not intended to substitute informed professional advice, I or mazdamenders.net cannot personally be hold responsible for any damage occurred from following this procedure or any injuries from it. Proceed at your own risk.


Mk 1 Eunos 93 black V.S II 1.8 fettled,
Mk 2 .1/4 Roadster 99 black & gold V.S 1.8 being rebuilt,
Mk 1 Eunos 90 1.6 (claimed by daughter)
Mk 1 Eunos 96 1.8 blue B2...being fettled
Mk1 Eunos 93 1.6 black S special being fettled
http://www.mx5oc.co.uk/ http://www.mx5nutz.com/forum/ http://miata.net/ http://www.autolinkuk.co.uk/

Return to “Members Mx-5/ Roadsters”

Who is online

Users browsing this forum: No registered users and 2 guests