What you put in, you'll get back ten fold
Members and searchers please be aware that some of our 'how to' guides do not currently show the intended help photos. This is because photobucket wants to charge a monthly amount for us to view our own pics. The photos are currently being replaced. If you need one of our guides and it is missing pics please let one of the Admin team know and we will make that one a priority for you.
Regards
Admin

Had a problem fitting a crankshaft seal?

Got a problem, need some advice ?
Get in here and ask the pros. There will always be one to bring you the correct answer, quickly.
Please bare in mind advice offered by some may not be correct. Pay attention to user ratings and status for a better idea on their knowledge.
User avatar
pollyanna
Regular
Posts: 72
Joined: Tue Feb 25, 2014 11:24 am

Had a problem fitting a crankshaft seal?

Postby pollyanna » Sun Apr 20, 2014 8:23 pm

Replacing the crankshaft seal on Mk1

Recently I had to do quite a lot of work on my Mk1 due to the Cambelt Idler Pulley disintegrating. While I had all the bits off I needed to replace this pulley. I also renewed all three belts Cambelt tensioner and spring, a few rubber pipes and new set of spark plugs etc.
I also replaced the Crankshaft Seal, which I found to be the most difficult part of the whole job as it is nigh impossible, I suspect, to fit without a special tool whatever that is. After spoiling one seal trying to fit it with a hammer and block of wood I decided to design and produce a tool for the job.
The sketch below gives the dimensions. As I didn't have any aluminium of the sizes required to turn I used,............some pieces of OAK would you believe. Being wood is was easy to turn.
Note: the ends of piece A and piece B must be square and true to the diameter of the pieces so that they present the seal accurately up to the housing that the seal is going in to.



The second sketch shows how it is used, using the crankshaft bolt to wind the “tool” in with the seal on the end of the piece marked A. Note: Make sure that when replacing the seal that you clean any of the old seal off the inside bore of the housing that it is going into. Also smear the inside of the housing and, the outside diameter and bore of the seal with grease to help it to slide in smoothly.
Crankshaft tool PS 1 JPEG.jpg
http://www.mazdamenders.net/forum/download/file.php?mode=view&id=3386&sid=5fc48e5678758eaaf20988107a3ebf62
Crankshaft tool PS 1 JPEG.jpg (72.15 KiB) Viewed 1902 times
Attachments
Crankshaft tool PS  2 JPEG.jpg
http://www.mazdamenders.net/forum/download/file.php?mode=view&id=3387&sid=5fc48e5678758eaaf20988107a3ebf62
Crankshaft tool PS 2 JPEG.jpg (67.96 KiB) Viewed 1902 times
Last edited by pollyanna on Mon Apr 21, 2014 10:04 am, edited 1 time in total.
User avatar
flea
Site Admin
Posts: 6618
Joined: Wed Dec 07, 2011 8:42 pm
Location: Medway towns, Kent

Re: Had a problem fitting a crankshaft seal?

Postby flea » Sun Apr 20, 2014 8:30 pm

:bow-yellow: :handgestures-thumbup:
Eunos 1.6 special 1989 with a few added extras
Eunos 1991 1.6
Eunos 1990 1.6 project
Mk2 1999 1.8
User avatar
Mazda Mender
Site Admin
Posts: 12190
Joined: Tue Dec 06, 2011 6:18 pm
Location: Pie land,North west
Contact:

Re: Had a problem fitting a crankshaft seal?

Postby Mazda Mender » Sun Apr 20, 2014 8:45 pm

Well done Al :bow-yellow: :handgestures-thumbup:
M-m
The Disclaimer:-
This post is a natural product made from recycled electrons. The slight variations in spelling and grammar enhance its individual character and beauty and in no way are to be considered flaws or defects, the articles/answers/comments are provided for information purposes and they are not intended to substitute informed professional advice, I or mazdamenders.net cannot personally be hold responsible for any damage occurred from following this procedure or any injuries from it. Proceed at your own risk.


Mk 1 Eunos 93 black V.S II 1.8 fettling,
Mk 2 .1/4 Roadster 99 black & gold V.S 1.8 being rebuilt,
Mk 1 Eunos 90 1.6 (claimed by daughter)
Mk 1 Eunos 96 1.8 blue B2...being fettled
Mk1 Eunos 93 1.6 black S special **gone**
http://www.mx5oc.co.uk/ http://www.mx5nutz.com/forum/ http://miata.net/ http://www.autolinkuk.co.uk/

Return to “Problems”

Who is online

Users browsing this forum: No registered users and 5 guests