What you put in, you'll get back ten fold
***** THIS IS VERY IMPORTANT TO THE SITE AND HELPING YOU,OTHERWISE IT CLOSES AND ALL THIS ON LINE GARAGE IS GONE FOR GOOD*****

Greetings and welcome to menders, this site was built for every owner that might need her to help keep those bills low and also keep them on the road where they belong, she is run by very passionate enthusiasts owners for passionate enthusiastic owners, see her like a on line garage, there is a lot of tech stuff hopefully explained for everyone to use, if there is something you cannot get your head around, or you feel that there is a strong walk through guide missing that needs creating by one of use or from yourselves, please let us know, we are also on false book and youtube, which as short tech vids to help, and again if you feel there is a vid that would help please get it touch.
the menders is free, but like everything there is a cost to run things and bills( we are just happy its not a heating cost), so if we have saved you hundreds, please throw a small donation in the pot so we can keep on going to carry on helping others in the same way .

*** we are currently looking for a sponsor for this year, so if you have the passion and can see this sites worth to everyone , please get in touch and step forward to help***

And thank heavens that we are now on the way back up the brighter ,warmer longer days, "come on summer", and lets see those project builds.


M-m

How to make a short intake for a MK 2/2.5...

User avatar
Mazda Mender
Site Admin
Posts: 15056
Joined: Tue Dec 06, 2011 6:18 pm
Location: Pie land, in the glen of Wiganshire
Contact:

How to make a short intake for a MK 2/2.5...

Postby Mazda Mender » Mon Nov 06, 2023 7:47 am

I often see this modification done badly when the reality is that its a very simple thing to make. I am also looking into this for the MK 1's which is a little more involved but not rocket science to do.

There is a marked benefit to having it this way and is a far better neater and cheap set up than the stupidly over priced Typhoon system by K & N which a lot of people are crazy enough to buy. Even second hand they are daft money for basically an alloy tube with a filter on the end.

Now the good thing about this being made is that you can fully custom with whichever filter shape, make or colour including the air intake hose. Personally I prefer the HKS mushroom filters as it gives a neat cleaner look but as you will see there are a number of options. For the guide we are using an oval K & N cone filter, simply because the owner of this car wanted that one fitting. So on to some parts needed:

References to what it will look like using different make filters and combos....

20211116_190815.jpg
20211116_190815.jpg (655.04 KiB) Viewed 513 times


20211118_152427.jpg
20211118_152427.jpg (628.14 KiB) Viewed 513 times


20231110_185044.jpg
20231110_185044.jpg (686.41 KiB) Viewed 509 times




1 x cone filter of chose
1 x 90 % bend air intake reducer hose( colour of chose) 70 mm x 65 mm
4 x 80-100 jubilee clips
1 x roll of black electrical tape
1 x selection of cable ties ( black)
1 x sikaflex or automotive sealant
1 x masking tape
1 x 8 mm inner/ 13mm outer of rubber/silicone hose( breather from the rocker cover) 2 meters long
1 x 8 mm inner / 12mm outer of rubber/silicone hose over flow hose from the rad to the expansion bottle) 1 meter long
1 x 10 mm barb
2 or 4 x jubilee clips 60-80mm

Tools needed....
1 x pointed pliers
1 x phillips driver or 10mm socket/1/4 ratchet
1 x drill
1 x step down drill bit or similar
1 x pair of snips
1 x utility knife
1 x marker pen
1 x 1/4 ratchet, extension,10 mm socket
1 x 3/8 ratchet, extension, 12mm & 14mm sockets

Pop the bonnet and prop it open safe and solid....

20231110_181613.jpg
20231110_181613.jpg (667.54 KiB) Viewed 508 times


Unplug the AFM,air sensor( release the loom lugs with the pointed pliers) and power steering plug(pointed pliers) and peel back the loom to the drivers side...

20231110_182025.jpg
20231110_182025.jpg (623.5 KiB) Viewed 508 times


20231110_182029.jpg
20231110_182029.jpg (612.53 KiB) Viewed 508 times


20231110_182039.jpg
20231110_182039.jpg (561.9 KiB) Viewed 508 times


20231110_182052.jpg
20231110_182052.jpg (601.08 KiB) Viewed 508 times


20231110_182057.jpg
20231110_182057.jpg (539.96 KiB) Viewed 508 times


20231110_182104.jpg
20231110_182104.jpg (546.08 KiB) Viewed 508 times


20231110_182111.jpg
20231110_182111.jpg (548.94 KiB) Viewed 508 times


20231110_182122.jpg
20231110_182122.jpg (443.14 KiB) Viewed 508 times


20231110_182134.jpg
20231110_182134.jpg (543.19 KiB) Viewed 508 times


20231110_182143.jpg
20231110_182143.jpg (550.34 KiB) Viewed 508 times


20231110_182148.jpg
20231110_182148.jpg (600.68 KiB) Viewed 508 times


Release the breather hose from the intake from the rocker cover.....

20231110_182021.jpg
20231110_182021.jpg (592.58 KiB) Viewed 508 times


Get your phillips driver or 1/4 drive ratchet, extension, 10mm socket and loosen the trunking clips on the AFM and throttle body...

20231110_182210.jpg
20231110_182210.jpg (615.44 KiB) Viewed 508 times


20231110_182221.jpg
20231110_182221.jpg (634.48 KiB) Viewed 508 times


And remove the intake trunking....

20231110_182231.jpg
20231110_182231.jpg (660.07 KiB) Viewed 508 times


20231110_182236.jpg
20231110_182236.jpg (651.84 KiB) Viewed 508 times


Get your ratchet,extension and 10mm socket and remove the 10mm head bolt that holds the air box snorkel and remove it....

20231110_182341.jpg
20231110_182341.jpg (492.13 KiB) Viewed 507 times


20231110_182300.jpg
20231110_182300.jpg (585.38 KiB) Viewed 507 times


20231110_182304.jpg
20231110_182304.jpg (560.75 KiB) Viewed 507 times


20231110_182321.jpg
20231110_182321.jpg (673.59 KiB) Viewed 507 times


Now get your ratchet ,extension and 12mm socket and remove the 12mm head nut at the front of the box and the 12mm head bolt hidden deep down at the back of the box, remove them box and pull the air box from out of the inner wing...

20231110_182419.jpg
20231110_182419.jpg (471.29 KiB) Viewed 507 times


20231110_182426.jpg
20231110_182426.jpg (589.84 KiB) Viewed 507 times


20231110_182517.jpg
20231110_182517.jpg (619.08 KiB) Viewed 507 times


Now get your ratchet and 10mm socket and remove the 2 x 10mm head bolts that hold the AFM to the air box and pull them apart, we need to reuse the AFM, the air box is no longer needed.

20231110_182552.jpg
20231110_182552.jpg (613.99 KiB) Viewed 507 times


20231110_182632.jpg
20231110_182632.jpg (595.27 KiB) Viewed 507 times


20231110_182635.jpg
20231110_182635.jpg (583.01 KiB) Viewed 507 times


20231110_182636.jpg
20231110_182636.jpg (577.13 KiB) Viewed 507 times


Now using a utility knife nice and gently, we need to peel back and seperate the air box sensor wires and plugs from with in the cable/loom trunking. There is a split in the trunking in which you can cut the tape along to open it up to pull the section out thats needs to be used on the other side...

20231110_182754.jpg
20231110_182754.jpg (588.86 KiB) Viewed 507 times


20231110_182912.jpg
20231110_182912.jpg (640.37 KiB) Viewed 507 times


20231110_183015.jpg
20231110_183015.jpg (650.09 KiB) Viewed 507 times


Now offer up your bend to see how much will need removing on the throttle body side and on the filter side, depending on the filter and set up, your AFM will need to be in the filter to help gauging fitment. Never over cut: it is easier to adjust with cutting more off than adding. Mark the cut all the way around with a marker pen, check and double check before cutting with whatever you find best; a very sharp utility knife is the choice of many (we use a very thin cutting disk in a grinder).

Once you are happy with all the fitment you need to mark where the air sensor is going to go. We also use the original rubber grommet it sits in from the OE air box. With the rocker cover breather hose barb, we fit this to the 90 degree bend, either with rubber washers to seal and standard washers and a nut to tighten up ,or with some sikaflex. Don't use sealant as its not strong enough. After a test fit, remove it all back off the Roadster for the drilling, fixing or bonding but please note:- if bonding then it will need to be left overnight to cure before final fitting up..

So on the table you can see that we have cut the 90 degree hose to the length we are happy with and drilled the hole for the air sensor on the back of the air filter and cut the hole for the barb for the rocker cover breather tube. We found that a step down drill bit works best. Go nice and slow, don't force as it will rip the hose to bits. Slow and steady is the way.

20231109_062604.jpg
20231109_062604.jpg (590.12 KiB) Viewed 506 times


20231109_062645.jpg
20231109_062645.jpg (433.89 KiB) Viewed 506 times


20231109_062702.jpg
20231109_062702.jpg (447.93 KiB) Viewed 506 times


20231031_180344.jpg
20231031_180344.jpg (279.96 KiB) Viewed 506 times


20231031_180355.jpg
20231031_180355.jpg (346.58 KiB) Viewed 506 times


20231031_180358.jpg
20231031_180358.jpg (281.14 KiB) Viewed 506 times


20231031_180402.jpg
20231031_180402.jpg (285.47 KiB) Viewed 506 times


20231031_180434.jpg
20231031_180434.jpg (300.39 KiB) Viewed 506 times


20231031_180441.jpg
20231031_180441.jpg (252.42 KiB) Viewed 506 times


And all lightly put together ready for fitment....

20231101_173216.jpg
20231101_173216.jpg (343.13 KiB) Viewed 506 times


20231101_173221.jpg
20231101_173221.jpg (319.55 KiB) Viewed 506 times


20231101_173251.jpg
20231101_173251.jpg (296.49 KiB) Viewed 506 times


20231101_173300.jpg
20231101_173300.jpg (334.08 KiB) Viewed 506 times


20231101_173322.jpg
20231101_173322.jpg (247.79 KiB) Viewed 506 times


20231101_173356.jpg
20231101_173356.jpg (262.58 KiB) Viewed 506 times


20231101_173500.jpg
20231101_173500.jpg (263.36 KiB) Viewed 506 times


20231101_173505.jpg
20231101_173505.jpg (257.78 KiB) Viewed 506 times


20231101_173519.jpg
20231101_173519.jpg (250.5 KiB) Viewed 506 times


Before final fitment we recommend that you change the expansion tank hose so it does not catch or rub on the filter. You will need 8 mm inner hose at 1 meter long or to your own spec. You will need to remove the drivers side radiator holding bracket on the top with a ratchet, extension and a 14mm socket. Then fit it to the expansion tank first and run in the way you want and to the rad inlet. Cut the hose down when happy and push on into place and bolt the retaining rad bracket back into place and you can start to fit everything back up. See pic below on the new hose reroute...

20231110_183320.jpg
20231110_183320.jpg (613.88 KiB) Viewed 506 times


Now we can start to add the AFM and the filter, air sensor, and twist and move into the best position before the final tightening up of all the jubilee clips and plugging everything back in to finalize the wiring route, re taping back up and tidying up/securing, and cable ties where needed(white was used in the guide as a reference
to be seen) adding the new breather hose 8 mm inner and 2 meters long and cut to the length you are happy with...

20231110_183449.jpg
20231110_183449.jpg (629.79 KiB) Viewed 506 times


20231110_185044.jpg
20231110_185044.jpg (686.41 KiB) Viewed 506 times


20231110_185051.jpg
20231110_185051.jpg (687.66 KiB) Viewed 506 times


20231110_185057.jpg
20231110_185057.jpg (575.98 KiB) Viewed 506 times


20231110_185100.jpg
20231110_185100.jpg (650.16 KiB) Viewed 506 times


20231110_185103.jpg
20231110_185103.jpg (643.76 KiB) Viewed 506 times


20231110_185114.jpg
20231110_185114.jpg (639.28 KiB) Viewed 506 times


And thats it all done and in working. Start her up to make sure everything is tight, rev her just for the hell of it...testing ;0), stand back and say " I did that"

As always any questions or if there is something that is not clear, please ask,we would rather you ask than struggle.
M-m
The Disclaimer:-
This post is a natural product made from recycled electrons. The slight variations in spelling and grammar enhance its individual character and beauty and in no way are to be considered flaws or defects, the articles/answers/comments are provided for information purposes and they are not intended to substitute informed professional advice, I or mazdamenders.net cannot personally be hold responsible for any damage occurred from following this procedure or any injuries from it. Proceed at your own risk.


Mk 1 Eunos 93 black V.S II 1.8 ,
Mk 2 .1/4 Roadster 99 black & gold V.S 1.8 .
Mk 1 Eunos 90 1.6 soul red ..f/ build
MK 2.1/4 Blue V.S Roadster 1.8 99 ..
MK1 1.8 ,white import.. (Ashleighs)
MK1 1.6 yellow J ltd import.f/build
MK 1 1.8 black Tokyo Ltd..f/build


http://www.mx5oc.co.uk/ http://www.mx5nutz.com/forum/ http://miata.net/ http://www.autolinkuk.co.uk/

Return to “MK2”

Who is online

Users browsing this forum: No registered users and 1 guest