/>
/> 
/> 
It is a very easy grill to fit with the basics of tools...
The kit contains...
1 x grill
2 x brackets
2 x phillips head screws
2 x bolts
2 x nuts
and a selection of washers
TOOLS REQUIRED...
1 x flat 10mm open and ring spanner
1 x 1/4 drive ratchet
1 x small 1/4 drive extension
1 x 10mm socket
1 x phillps driver
20-30 minutes to fit..
So what we get...
- 20240713_132627.jpg (831.14 KiB) Viewed 1301 times
- 20240713_133347.jpg (678.56 KiB) Viewed 1301 times
- 20240728_115558.jpg (723.36 KiB) Viewed 1301 times
Take 2 x bolts and add one of the large penny washers...
- 20240728_115633.jpg (672.83 KiB) Viewed 1300 times
Then place them into the 2 x centre holes( the bolts that come with the kit will be shorter)...
- 20240728_115651.jpg (498.26 KiB) Viewed 1300 times
Slide the other large penny washer on and offer the support brackets to the bolts then adding the small washer and nut by fingers...
- 20240728_115815.jpg (550.6 KiB) Viewed 1300 times
- 20240728_115817.jpg (540.96 KiB) Viewed 1300 times
Slide the 10mm spanner ring end onto the bolt head in the impact bumper to hold it firm while you tighten the nut with the ratchet and 10mm socket. Now tighten up nice and firm and spin the bracket around so it hides the bolt etc...
- 20240728_120029.jpg (754.29 KiB) Viewed 1300 times
- 20240728_120420.jpg (584.35 KiB) Viewed 1300 times
- 20240728_120428.jpg (591.96 KiB) Viewed 1300 times
- 20240728_120434.jpg (539.46 KiB) Viewed 1300 times
- 20240728_120440.jpg (586.85 KiB) Viewed 1300 times
- 20240728_120444.jpg (547.04 KiB) Viewed 1300 times
Now get the grill and slide it over the tie down baby teeth, it is not meant to go flat against the air guide by design, it is meant to be curved...
- 20240728_120505.jpg (761.7 KiB) Viewed 1300 times
- 20240728_120545.jpg (721.37 KiB) Viewed 1300 times
- 20240728_120548.jpg (701.41 KiB) Viewed 1300 times
- 20240728_120550.jpg (739.74 KiB) Viewed 1300 times
- 20240728_120554.jpg (752.63 KiB) Viewed 1300 times
Now get the 2 x phillips head screws and driver and located the fixing holes in the brackets now behind the grill and screw them down nice and tight to hold the grill solid...
- 20240728_120620.jpg (707.73 KiB) Viewed 1300 times
- 20240728_121158.jpg (735.26 KiB) Viewed 1300 times
- 20240728_121209.jpg (686.88 KiB) Viewed 1300 times
- 20240728_121214.jpg (659.74 KiB) Viewed 1300 times
- 20240728_121218.jpg (758.98 KiB) Viewed 1300 times
- 20240728_121222.jpg (751.33 KiB) Viewed 1300 times
- 20240728_121226.jpg (730.37 KiB) Viewed 1300 times
And thats it, simple, easy install and looks good and its also doing a job at the same time. Link at the top and below. They also do grills for the other marks, which can be found on the Jass website in the search bar.
As is the norm, any questions, please ask, don't ever struggle.
M-m
