After removing the caliper from the car you'll first need to remove the dust bolt that covers the adjuster shown here.
With an Allen key unwind the adjuster until you feel it has come away from the worm drive within the calliper. This is done by turning in a clockwise direction.
Once this is done then you can pull the piston from the housing. If it's a bit stubborn then you can shift it by using an air hose as shown below. If you do this make sure your hand is ready to stop the piston from shooting out & getting damaged. I found short blasts were best.
Then remove the dust rubber cover.
Now remove the seal within the chamber.
Now you'll need a long slim pair of cir-clip pliers to remove the cir-clip inside the chamber .
I tried to find a pair but couldn't find any. So a little tip. If you buy the Draper cheap ones then you can drill two additional holes which makes them long enough to reach the clip.
Before I drilled.
And after, showing the two new holes. This will make things a lot easier.
Now remove the cir-clip at the bottom of the chamber which holds the worm drive in place.
Remove the worm drive.
Also the little pin located behind it.
Now you can remove the hand brake lever.
Now you'll need to wash & clean out the calliper body including all the areas where the new rubbers are to go. I finished by blowing the unit out with an air-gun just to make sure there was no debris left at all.
Also clean the piston & other moving parts. I used flour paper as this will not damage any of the surfaces.
Also remove the rubber on the end of the worm drive.
Now you have cleaned everything you are ready to put back together. Note: these are new rubbers and not the original old ones.
Fit the new seal to the end of the worm drive.
Also the inner seal.
Make sure its sitting correctly.
Remove the seal where the hand brake shaft passes through the calliper body.
Clean this area up. Put a little grease on the new seal.
And push firmly into place.
Put some grease on the end of the worm drive like so. I don't like to put grease on any of the parts that are in contact with brake fluid so as not to contaminate the fluid.
Also the little pin that goes in the end.
Also grease the shaft of the hand brake lever.
Then push the lever shaft back into the body.
Then, with the pin also greased placed at the end of the worm drive, place it back within the calliper body like so. If you move the hand brake lever it will become obvious where the little pin is to be located as there is a little notch in the shaft of the hand brake lever.
You will know when its in the correct place by moving the hand brake lever. This will move the worm drive in & out. Then replace the cir-clip.
Rather than using brake calliper lubricant to install the other rubbers I use the same brake fluid that I use in the braking system on the car. It works really well. So put a little on your finger & wipe it around the inner seal.
Also put some brake fluid on the piston & place the dust cover rubber over the piston starting from the outer end. It will locate in the groove that it is meant to sit in but just go past this until it is at the other end of the piston. You need to have the section of the rubber that is to go within the calliper sticking over from the end of the piston as shown in the picture.
Now feed the rubber into the groove in which it is intended to go. Start at the bottom & work your way around. You can make sure its OK by holding the rubber with your thumb & fore-finger then give it a little twist.
Then grease up & replace the adjuster.
Now turn the adjuster using an Allen key. Turning anti clockwise. You will probably have to put a little pressure on the piston until it locates & starts to wind in.
Once wound fully in, the dust rubber will locate itself into the groove. Don't forget the brake fluid on the rubber & piston. It makes the job a lot easier.
Now put a smear of grease on the slide pin rubbers & push into place.
Now for replacing the spring to the hand brake lever. Place it over the center pillar like so with the straighter part behind the stop as shown.
Now with a pair of pliers grip this section & pull it over the lever part like so.
Put a little grease on the thread of the bleed screw & replace that.
There you go. One refurbished calliper.
What you put in, you'll get back ten fold
***** THIS IS VERY IMPORTANT TO THE SITE AND HELPING YOU,OTHERWISE IT CLOSES AND ALL THIS ON LINE GARAGE IS GONE FOR GOOD*****
Greetings and welcome to menders, this site was built for every owner that might need her to help keep those bills low and also keep them on the road where they belong, she is run by very passionate enthusiasts owners for passionate enthusiastic owners, see her like a on line garage, there is a lot of tech stuff hopefully explained for everyone to use, if there is something you cannot get your head around, or you feel that there is a strong walk through guide missing that needs creating by one of us or from yourselves, please let us know, we are also on false book and youtube, which as short tech vids to help, and again if you feel there is a vid that would help please get it touch.
the menders is free, but like everything there is a cost to run things and bills( we are just happy its not a heating cost), so if we have saved you hundreds, please throw a small donation in the pot so we can keep on going to carry on helping others in the same way .
*** we are currently looking for a sponsor for this year, so if you have the passion and can see this sites worth to everyone , please get in touch and step forward to help***
And thank heavens that we are now on the way back up the brighter ,warmer longer days, "come on summer", and lets see those project builds.
M-m
Greetings and welcome to menders, this site was built for every owner that might need her to help keep those bills low and also keep them on the road where they belong, she is run by very passionate enthusiasts owners for passionate enthusiastic owners, see her like a on line garage, there is a lot of tech stuff hopefully explained for everyone to use, if there is something you cannot get your head around, or you feel that there is a strong walk through guide missing that needs creating by one of us or from yourselves, please let us know, we are also on false book and youtube, which as short tech vids to help, and again if you feel there is a vid that would help please get it touch.
the menders is free, but like everything there is a cost to run things and bills( we are just happy its not a heating cost), so if we have saved you hundreds, please throw a small donation in the pot so we can keep on going to carry on helping others in the same way .
*** we are currently looking for a sponsor for this year, so if you have the passion and can see this sites worth to everyone , please get in touch and step forward to help***
And thank heavens that we are now on the way back up the brighter ,warmer longer days, "come on summer", and lets see those project builds.
M-m
MK1 Rear Brake Caliper Overhaul
MK1 Rear Brake Caliper Overhaul
- Attachments
-
- rc47.JPG (32.49 KiB) Viewed 21472 times
-
- rc12.JPG (27.94 KiB) Viewed 21472 times
-
- rc9.JPG (14.77 KiB) Viewed 21472 times
Eunos 1.6 special 1989 with a few added extras
Eunos 1991 1.6
Eunos 1990 1.6 project
Mk2 1999 1.8
Eunos 1991 1.6
Eunos 1990 1.6 project
Mk2 1999 1.8
- Mazda Mender
- Site Admin
- Posts: 15100
- Joined: Tue Dec 06, 2011 6:18 pm
- Location: Pie land, in the glen of Wiganshire
- Contact:
Re: Mk1 rear break caliper overhaul
Well done Royster, very good write up and plenty of pic's which makes it easier to follow for owners who are unsure.
The Disclaimer:-
This post is a natural product made from recycled electrons. The slight variations in spelling and grammar enhance its individual character and beauty and in no way are to be considered flaws or defects, the articles/answers/comments are provided for information purposes and they are not intended to substitute informed professional advice, I or mazdamenders.net cannot personally be hold responsible for any damage occurred from following this procedure or any injuries from it. Proceed at your own risk.
Mk 1 Eunos 93 black V.S II 1.8 ,
Mk 2 .1/4 Roadster 99 black & gold V.S 1.8 .
Mk 1 Eunos 90 1.6 soul red ..f/ build
MK 2.1/4 Blue V.S Roadster 1.8 99 ..
MK1 1.8 ,white import.. (Ashleighs)
MK1 1.6 yellow J ltd import.f/build
MK 1 1.8 black Tokyo Ltd..f/build
http://www.mx5oc.co.uk/ http://www.mx5nutz.com/forum/ http://miata.net/ http://www.autolinkuk.co.uk/
This post is a natural product made from recycled electrons. The slight variations in spelling and grammar enhance its individual character and beauty and in no way are to be considered flaws or defects, the articles/answers/comments are provided for information purposes and they are not intended to substitute informed professional advice, I or mazdamenders.net cannot personally be hold responsible for any damage occurred from following this procedure or any injuries from it. Proceed at your own risk.
Mk 1 Eunos 93 black V.S II 1.8 ,
Mk 2 .1/4 Roadster 99 black & gold V.S 1.8 .
Mk 1 Eunos 90 1.6 soul red ..f/ build
MK 2.1/4 Blue V.S Roadster 1.8 99 ..
MK1 1.8 ,white import.. (Ashleighs)
MK1 1.6 yellow J ltd import.f/build
MK 1 1.8 black Tokyo Ltd..f/build
http://www.mx5oc.co.uk/ http://www.mx5nutz.com/forum/ http://miata.net/ http://www.autolinkuk.co.uk/
Re: Mk1 rear break caliper overhaul
Cheers buddy. I'll do the front ones too
Eunos 1.6 special 1989 with a few added extras
Eunos 1991 1.6
Eunos 1990 1.6 project
Mk2 1999 1.8
Eunos 1991 1.6
Eunos 1990 1.6 project
Mk2 1999 1.8
Re: Mk1 rear break caliper overhaul
Great write up Mr Flea
1989 Fresh import with 30,000 km, Maruha Four Pot calipers, 270mm disks, Rose jointed drop links, Uprated ARB's, MeisterR CRD Coilovers, Rota wheels, LSD, Zoom console, Maruha Alternator, Jenvey ITB's, Megasquirt ECU
1st Modified Class Bristol OC Spring Rally
2nd Weston Park April 2017
1st 'Modern Classic' Stafford Castle Classic Show July 2018
3rd 'Best Japanese Classic' Tatton Park Aug 18
1st Modified Class Ragley Hall OC National SEP 18
1st Easter show Weston Park 2019
2nd 80's class Newport Easter show 2019
2011 2.0 RC Sport Tech in Aluminium, Smart Top.
1st Modified Class Bristol OC Spring Rally
2nd Weston Park April 2017
1st 'Modern Classic' Stafford Castle Classic Show July 2018
3rd 'Best Japanese Classic' Tatton Park Aug 18
1st Modified Class Ragley Hall OC National SEP 18
1st Easter show Weston Park 2019
2nd 80's class Newport Easter show 2019
2011 2.0 RC Sport Tech in Aluminium, Smart Top.
-
- Turbo Charged
- Posts: 2383
- Joined: Wed Dec 07, 2011 8:53 pm
Re: MK1 Rear Brake Caliper Overhaul
Morning................Cheers mate
Eunos 1.6 special 1989 with a few added extras
Eunos 1991 1.6
Eunos 1990 1.6 project
Mk2 1999 1.8
Eunos 1991 1.6
Eunos 1990 1.6 project
Mk2 1999 1.8
Re: MK1 Rear Brake Caliper Overhaul
Superb write-up! Looks like a perfect step-by-step guide to me, almost idiot-proof!
A couple of minor things I'd like to see added is just at the top, which tools & fluids you are using. Just a basic list of DOT 4.0 brake fluid, calliper grease (make the point that copper grease isn't calliper grease), 13mm spanner etc.
Also a quick question. The cir-clip pliers; it looks like you are just using standard pin long-nose cir-clip pliers so how does drilling holes in them help?
A couple of minor things I'd like to see added is just at the top, which tools & fluids you are using. Just a basic list of DOT 4.0 brake fluid, calliper grease (make the point that copper grease isn't calliper grease), 13mm spanner etc.
Also a quick question. The cir-clip pliers; it looks like you are just using standard pin long-nose cir-clip pliers so how does drilling holes in them help?
Lazza
2001 Mk2.5 MX5 1.8 Sport
Hard Dog Deuce
GAZ Gold Pro
Mk3 seats
17” OZ Racing Superturissmo wheels (for the toad)
15” Rota Circuit 10 wheels (for track use)
2001 Mk2.5 MX5 1.8 Sport
Hard Dog Deuce
GAZ Gold Pro
Mk3 seats
17” OZ Racing Superturissmo wheels (for the toad)
15” Rota Circuit 10 wheels (for track use)
Re: MK1 Rear Brake Caliper Overhaul
Good point Lazza. The reason for the additional holes was it makes the reach longer otherwise you can't get hold of the circlip. I'll check out what i wrote & see that it makes sence
Eunos 1.6 special 1989 with a few added extras
Eunos 1991 1.6
Eunos 1990 1.6 project
Mk2 1999 1.8
Eunos 1991 1.6
Eunos 1990 1.6 project
Mk2 1999 1.8
Re: MK1 Rear Brake Caliper Overhaul
Lazza i have explained the reason already???
Eunos 1.6 special 1989 with a few added extras
Eunos 1991 1.6
Eunos 1990 1.6 project
Mk2 1999 1.8
Eunos 1991 1.6
Eunos 1990 1.6 project
Mk2 1999 1.8
Re: MK1 Rear Brake Caliper Overhaul
Does anyone know what size the alen key it is?. Mine are not marked, i just found one that fitted
Eunos 1.6 special 1989 with a few added extras
Eunos 1991 1.6
Eunos 1990 1.6 project
Mk2 1999 1.8
Eunos 1991 1.6
Eunos 1990 1.6 project
Mk2 1999 1.8
Re: MK1 Rear Brake Caliper Overhaul
Yes you did explain but I don't understand how drilling holes in it makes the reach longer... maybe I'm being a bit simple
Lazza
2001 Mk2.5 MX5 1.8 Sport
Hard Dog Deuce
GAZ Gold Pro
Mk3 seats
17” OZ Racing Superturissmo wheels (for the toad)
15” Rota Circuit 10 wheels (for track use)
2001 Mk2.5 MX5 1.8 Sport
Hard Dog Deuce
GAZ Gold Pro
Mk3 seats
17” OZ Racing Superturissmo wheels (for the toad)
15” Rota Circuit 10 wheels (for track use)
Re: MK1 Rear Brake Caliper Overhaul
Lazza wrote:Yes you did explain but I don't understand how drilling holes in it makes the reach longer... maybe I'm being a bit simple
By drilling the new holes it just extends the nose of the pliers enough to reach the circlip. Without doing this you can't get hold of it. I tried everywhere to get some that would do the job so reolized by doing this it worked fine Now has the penny dropped
Eunos 1.6 special 1989 with a few added extras
Eunos 1991 1.6
Eunos 1990 1.6 project
Mk2 1999 1.8
Eunos 1991 1.6
Eunos 1990 1.6 project
Mk2 1999 1.8
Re: MK1 Rear Brake Caliper Overhaul
Nope. I don't see how the holes extend the reach...
I just tried to repost the 2 pictures here but can't seem to do it.
I just tried to repost the 2 pictures here but can't seem to do it.
Lazza
2001 Mk2.5 MX5 1.8 Sport
Hard Dog Deuce
GAZ Gold Pro
Mk3 seats
17” OZ Racing Superturissmo wheels (for the toad)
15” Rota Circuit 10 wheels (for track use)
2001 Mk2.5 MX5 1.8 Sport
Hard Dog Deuce
GAZ Gold Pro
Mk3 seats
17” OZ Racing Superturissmo wheels (for the toad)
15” Rota Circuit 10 wheels (for track use)
Re: MK1 Rear Brake Caliper Overhaul
Ah! Just worked it out! It's not just holes drilled in the pliers, you are remounting the pivot! That makes sense but I have to say, the pictures & text don't describe that at all. It reads and looks like you just take the pliers, drill holes in them and that somehow, magically extends the reach!
Lazza
2001 Mk2.5 MX5 1.8 Sport
Hard Dog Deuce
GAZ Gold Pro
Mk3 seats
17” OZ Racing Superturissmo wheels (for the toad)
15” Rota Circuit 10 wheels (for track use)
2001 Mk2.5 MX5 1.8 Sport
Hard Dog Deuce
GAZ Gold Pro
Mk3 seats
17” OZ Racing Superturissmo wheels (for the toad)
15” Rota Circuit 10 wheels (for track use)
Re: MK1 Rear Brake Caliper Overhaul
imagine how they are being used. The handle part gets in the way & catches the rim of the piston. When you drill the new holes it makes the handles further away from the end of the pliers therefore it don't catch the rim of the piston & you can still open & close them to get hold of the circlip. Shall i draw a picture?
Eunos 1.6 special 1989 with a few added extras
Eunos 1991 1.6
Eunos 1990 1.6 project
Mk2 1999 1.8
Eunos 1991 1.6
Eunos 1990 1.6 project
Mk2 1999 1.8
Who is online
Users browsing this forum: No registered users and 1 guest